manualshive.com logo in svg

Yamaha GRIZZLY 350 YFM35GZ, Owner'S Manual, Page: 111 / 138

Share
Download
Yamaha GRIZZLY 350 YFM35GZ Owner'S Manual Download Page 111

8-32

8

4. Tighten the locknut at the brake lever.

TIP

When adjusting the rear brake lever free play:

●

Be sure not to step on the brake pedal.

●

Make sure the brake pedal does not move.

Checking the brake pedal position

The top of the brake pedal should be positioned
72.0–82.0 mm (2.83–3.23 in) above the footboard
bracket. If the brake pedal position is incorrect,
have a Yamaha dealer adjust it.

EBU24754

Brake light switches 

The brake light, which is activated by the brake
pedal and brake levers, should come on just be-
fore braking takes effect.
The brake light switch for the brake pedal can be
adjusted as follows, but the other brake light
switches should be adjusted by a Yamaha dealer.

1. Remove panel A. (See page 8-9.)
2. Turn the brake light switch adjusting nut while

holding the brake light switch in place. To
make the brake light come on earlier, turn the
adjusting nut in direction (a). To make the
brake light come on later, turn the adjusting
nut in direction (b).

1. Locknut

2. Brake lever free play adjusting bolt

1

2

(a)

(b)

1. Distance between brake pedal and footboard bracket

1

1

U5WH66E0.book  Page 32  Thursday, June 18, 2009  10:41 AM

Summary of Contents for GRIZZLY 350 YFM35GZ











































































































































Reviews:

No comments