manualshive.com logo in svg

Yamaha GRIZZLY 350 YFM35GZ, Owner'S Manual, Page: 104 / 138

Share
Download
Yamaha GRIZZLY 350 YFM35GZ Owner'S Manual Download Page 104

8-25

8

TIP

If the specified idling speed cannot be obtained as
described above, have a Yamaha dealer make the
adjustment.

EBU24045

Adjusting the throttle cable free play 

The throttle cable free play should be checked
and, if necessary, adjusted at the intervals speci-
fied in the periodic maintenance and lubrication
chart.
The throttle cable free play should measure 3.0–
5.0 mm (0.12–0.20 in) at the throttle lever. Period-
ically check the throttle cable free play and, if nec-
essary, adjust it as follows.

TIP

The engine idling speed must be checked, and ad-
justed if necessary, before adjusting the throttle ca-
ble free play.

1. Slide the rubber cover back.
2. Loosen the locknut.
3. To increase the throttle cable free play, turn

the throttle cable free play adjusting bolt in di-
rection (a). To decrease the throttle cable free
play, turn the adjusting bolt in direction (b).

1. Throttle stop screw

Engine idling speed:

1450–1550 r/min

U5WH66E0.book  Page 25  Thursday, June 18, 2009  10:41 AM

Summary of Contents for GRIZZLY 350 YFM35GZ











































































































































Reviews:

No comments