Yamaha GRIZZLY 350 YFM35GW Owner'S Manual Download | Manualshive

Page: 33 / 134

background image

4-11

4

ON

With the fuel cock lever in this position, fuel flows
to the carburetor. Turn the fuel cock lever to this
position when starting the engine and riding.

RES

This indicates reserve. With the fuel cock lever in
this position, the fuel reserve is made available.
Turn the fuel cock lever to this position if you run
out of fuel while riding. When this occurs, refuel as
soon as possible and be sure to turn the fuel cock
lever back to “ON”!

EBU18850

Starter (choke) “

”

Starting a cold engine requires a richer air-fuel mix-
ture, which is supplied by the starter (choke).
Move the starter (choke) in direction (a) to turn on
the starter (choke).

1. Arrow mark pointing to “ON”

1. Arrow mark pointing to “RES”

U5WH63E0.book Page 11 Monday, May 8, 2006 1:25 PM

«
...
31
32
33
34
35
...
»

Summary of Contents for GRIZZLY 350 YFM35GW







































































































































Reviews:

No comments

Related manuals for GRIZZLY 350 YFM35GW

RAPTOR YFM660RR

Brand: Yamaha Pages: 424

Brand: Yamaha Pages: 342

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands