Yamaha GRIZZLY 350 YFM35GW Owner'S Manual Download

Page: 123 / 134

10-1

EBU25960

SPECIFICATIONS

Dimensions:

Overall length:

1984 mm (78.1 in)

Overall width:

1085 mm (42.7 in)

Overall height:

1120 mm (44.1 in)

Seat height:

827 mm (32.6 in)

Wheelbase:

1233 mm (48.5 in)

Ground clearance:

245 mm (9.6 in)

Minimum turning radius:

3000 mm (118 in)

Weight:

With oil and fuel:

245.0 kg (540 lb) (EUR)(GBR)
249.0 kg (549 lb) (AUS)(NZL)

Noise and vibration level:

Noise level (77/311/EEC):

77.6 dB(A) (EUR)(GBR)

Vibration on seat (EN1032, ISO5008):

Will not exceed 0.5 m/s² (EUR)(GBR)

Vibration on handlebar (EN1032, ISO5008):

Will not exceed 2.5 m/s² (EUR)(GBR)

Engine:

Engine type:

Air cooled 4-stroke, SOHC

Cylinder arrangement:

Forward-inclined single cylinder

Displacement:

348.0 cm³

Bore

stroke:

83.0

64.5 mm (3.27

2.54 in)

Compression ratio:

9.20 :1

Starting system:

Electric and recoil starter

Lubrication system:

Wet sump

U5WH63E0.book Page 1 Monday, May 8, 2006 1:25 PM

Summary of Contents for GRIZZLY 350 YFM35GW







































































































































Search results

Summary of Contents for GRIZZLY 350 YFM35GW

Reviews:

Related manuals for GRIZZLY 350 YFM35GW

Brands by name

Popular brands

Yamaha GRIZZLY 350 YFM35GW, Owner'S Manual

Search results

Summary of Contents for GRIZZLY 350 YFM35GW

Reviews:

Related manuals for GRIZZLY 350 YFM35GW

Brands by name

Popular brands