manualshive.com logo in svg

Yamaha GRIZZLY 350 YFM35GW, Owner'S Manual

The Yamaha GRIZZLY 350 YFM35GW is a powerful and reliable all-terrain vehicle designed to tackle any outdoor adventure. To ensure optimal performance and maintenance, it is essential to refer to the comprehensive Owner's Manual. Download your free copy of the manual from manualshive.com today and unlock the full potential of your GRIZZLY 350.

Share
Download
background image

8-40

8

2. Elevate the ATV and place a suitable stand

under the frame.

3. Remove the nuts from the wheel.
4. Remove the wheel.

EBU25700

Installing a wheel 

1. Install the wheel and the nuts.

NOTE:

●

The arrow mark 

 on the tire must point toward

the rotating direction of the wheel.

●

Tapered nuts are used for both the front and rear
wheels. Install the nuts with their tapered side to-
wards the wheel.

1. Wheel nut

1. Arrow mark

U5WH63E0.book  Page 40  Monday, May 8, 2006  1:25 PM

Summary of Contents for GRIZZLY 350 YFM35GW







































































































































Reviews:

No comments

Related manuals for GRIZZLY 350 YFM35GW

Brands by name

Popular brands

Load more brands