manualshive.com logo in svg

Yamaha GRIZZLY 350 YFM35GW, Owner'S Manual

The Yamaha GRIZZLY 350 YFM35GW is a powerful and reliable all-terrain vehicle designed to tackle any outdoor adventure. To ensure optimal performance and maintenance, it is essential to refer to the comprehensive Owner's Manual. Download your free copy of the manual from manualshive.com today and unlock the full potential of your GRIZZLY 350.

Share
Download
background image

8-37

8

EBU26902

Replacing a headlight bulb 

If a headlight bulb burns out, replace it as follows.

1. Remove the bulb holder cover at the rear of

the headlight by pulling it off.

2. Disconnect the headlight coupler by lifting the

tab as shown and pulling out the coupler.

3. Remove the headlight bulb holder assembly

by turning it counterclockwise.

1. Headlight bulb holder cover

1. Headlight coupler

1. Headlight bulb holder assembly

U5WH63E0.book  Page 37  Monday, May 8, 2006  1:25 PM

Summary of Contents for GRIZZLY 350 YFM35GW







































































































































Reviews:

No comments

Related manuals for GRIZZLY 350 YFM35GW

Brands by name

Popular brands

Load more brands