Yamaha GRIZZLY 350 YFM35GW Owner'S Manual Download

Page: 110 / 134

8-33

EBU25040

Lubricating the upper and lower arm
pivots

The upper and lower arm pivots must be lubricated
at the intervals specified in the periodic mainte-
nance and lubrication chart.

EBU25080

Lubricating the knuckle shafts

The knuckle shafts must be lubricated at the inter-
vals specified in the periodic maintenance and lu-
brication chart.

EBU25100

Lubricating the steering shaft

The steering shaft must be lubricated at the inter-
vals specified in the periodic maintenance and lu-
brication chart.

EBU25222

Battery

This model is equipped with a sealed-type (MF)
battery, which does not require any maintenance.
There is no need to check the electrolyte or to add
distilled water. Check and, if necessary, tighten the
battery lead connections.

CAUTION:

ECB00620

Never attempt to remove the battery cell seals,
as this would permanently damage the battery.

Recommended lubricant:

Lithium-soap-based grease

Recommended lubricant:

Lithium-soap-based grease

Recommended lubricant:

Lithium-soap-based grease

Recommended lubricant:

Lithium-soap-based grease

U5WH63E0.book Page 33 Monday, May 8, 2006 1:25 PM

Summary of Contents for GRIZZLY 350 YFM35GW







































































































































Search results

Summary of Contents for GRIZZLY 350 YFM35GW

Reviews:

Related manuals for GRIZZLY 350 YFM35GW

Brands by name

Popular brands

Yamaha GRIZZLY 350 YFM35GW, Owner'S Manual

Search results

Summary of Contents for GRIZZLY 350 YFM35GW

Reviews:

Related manuals for GRIZZLY 350 YFM35GW

Brands by name

Popular brands