Yamaha GRIZZLY 350 YFM35FGY Owner'S Manual Download | Manualshive

Page: 41 / 138

background image

5-1

5

EBU19200

PRE-OPERATION CHECKS

EBU19223

Pre-operation check list

Before operating this ATV, be sure to check the items listed in the following table.

WARNING

EWB00480

Always inspect your ATV each time you use it to make sure it is in safe operating condition.
Always follow the inspection and maintenance procedures and schedules described in the Owner’s
Manual. Failure to inspect increases the possibility of an accident or equipment damage.

TIP

The maintenance of some items in the table has to be performed by a Yamaha dealer. Refer to the periodic
maintenance charts on page 8-3 to determine which service should be performed by a Yamaha dealer.

ITEM

ROUTINE

PAGE

Fuel

• Check fuel level in fuel tank, and add recommended fuel if neces-

sary.

• Check fuel line for leakage. Correct if necessary.

Engine oil

• Check oil level in engine, and add recommended oil to specified lev-

el if necessary.

• Check ATV for oil leakage. Correct if necessary.

Final gear oil

• Check ATV for oil leakage. Correct if necessary.

Differential gear oil

• Check ATV for oil leakage. Correct if necessary.

U5UH65E0.book Page 1 Monday, June 16, 2008 10:34 AM

«
...
39
40
41
42
43
...
»

Summary of Contents for GRIZZLY 350 YFM35FGY











































































































































Reviews:

No comments

Related manuals for GRIZZLY 350 YFM35FGY

WOLVERINE YFM45FXV

Brand: Yamaha Pages: 34

BLASTER YFS200S

Brand: Yamaha Pages: 46

Brand: Baja motorsports Pages: 18

1970 SKI-DADDLER

Brand: AMF Pages: 74

Brand: Hisun Pages: 61

PAVER SPECIAL RPS Series

Brand: Etnyre Pages: 61

Brand: Yutrax Pages: 8

Brand: Linhai Pages: 92

Brand: Strongway Pages: 3

Brand: MasterCraft Pages: 33

2016 Grizzly yfm700gplg

Brand: Yamaha Pages: 474

Brand: MULTIQUIP Pages: 54

Brand: E-TON Pages: 24

Brand: Yamaha Pages: 374

Brand: ReelCraft Pages: 8

Brand: Remote Access Vehicles, Corp. Pages: 9

Brand: New Leader Pages: 116

Brand: DINO CARS Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands