Yamaha GRIZZLY 350 YFM35FGY Owner'S Manual Download | Manualshive

Page: 35 / 138

background image

4-13

4

RES

This indicates reserve. With the fuel cock lever in
this position, the fuel reserve is made available.
Turn the fuel cock lever to this position if you run
out of fuel while riding. When this occurs, refuel as
soon as possible and be sure to turn the fuel cock
lever back to “ON”!

EBU18850

Starter (choke) “

”

Starting a cold engine requires a richer air-fuel mix-
ture, which is supplied by the starter (choke).
Move the starter (choke) in direction (a) to turn on
the starter (choke).

Move the starter (choke) in direction (b) to turn off
the starter (choke).
See the “Starting a cold engine” section on page
6-1 for proper operation.

EBU18880

Seat

To remove the seat

Pull the seat lock lever upward and pull up the seat
at the rear.

1. Arrow mark pointing to “RES”

1. Starter (choke) “

”

U5UH65E0.book Page 13 Monday, June 16, 2008 10:34 AM

«
...
33
34
35
36
37
...
»

Summary of Contents for GRIZZLY 350 YFM35FGY











































































































































Reviews:

No comments

Related manuals for GRIZZLY 350 YFM35FGY

Brand: Nakayama Pages: 14

Lynx 1200 4-TEC 900 ACE 2018

Brand: BRP Pages: 164

Brand: BOMBARDIER Pages: 328

Brand: Toro Pages: 28

Brand: Suzuki Pages: 624

Brand: Seizmik Pages: 10

Brand: ASV Pages: 60

Brand: Duralite Pages: 27

Brand: Ultra-tow Pages: 15

Brand: TrailMaster Pages: 7

Brand: TrailMaster Pages: 22

Stockchaser IS12 2017

Brand: Columbia Pages: 36

Summit SU5-L-2 2017

Brand: Columbia Pages: 40

Sportsman 90 2011

Brand: Polaris Pages: 12

Brand: Polaris Pages: 346

Brand: Valor Pages: 41

QuicKART 2000 Series

Brand: Dane Technologies Pages: 115

Brand: Xingyun Pages: 92

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands