manualshive.com logo in svg

Yamaha GRIZZLY 350 YFM35FGY, Owner'S Manual

Share
Download
Yamaha GRIZZLY 350 YFM35FGY Owner'S Manual Download Page 121

8-43

8

To raise a headlight beam, turn the headlight beam
adjusting screw in direction (a).
To lower a headlight beam, turn the adjusting
screw in direction (b).

EBU25580

Replacing the tail/brake light bulb 

If the tail/brake light bulb burns out, have a
Yamaha dealer replace it.

EBU25651

Removing a wheel 

1. Place the ATV on a level surface.
2. Loosen the wheel nuts.

3. Elevate the ATV and place a suitable stand

under the frame.

4. Remove the nuts from the wheel.
5. Remove the wheel.

EBU25701

Installing a wheel 

1. Place the ATV on a level surface.
2. Install the wheel and the nuts.

TIP

●

The arrow mark 

 on the tire must point toward

the rotating direction of the wheel.

1. Headlight beam adjusting screw

1. Wheel nut

U5UH65E0.book  Page 43  Monday, June 16, 2008  10:34 AM

Summary of Contents for GRIZZLY 350 YFM35FGY











































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands