manualshive.com logo in svg

Yamaha GRIZZLY 350 YFM35FGY, Owner'S Manual

Share
Download
Yamaha GRIZZLY 350 YFM35FGY Owner'S Manual Download Page 108

8-30

8

●

Make sure the brakes operate smoothly and
that there is no free play.

●

Make sure the brakes do not drag.

●

Make sure the brakes are not spongy. All air
must be bled from the brake system.

Replacement of brake components requires
professional knowledge. These procedures
should be performed by a Yamaha dealer.

EBU24513

Adjusting the brake pedal and rear 
brake lever free play and checking the 
brake pedal position 

The brake pedal and brake lever free play must be
checked and, if necessary, adjusted at the inter-
vals specified in the periodic maintenance and lu-
brication chart.

TIP

●

Always perform this maintenance completely in
the following order whenever adjusting the rear
brake.

●

Before adjusting the brake lever and brake pedal
free play, check the rear brake shoes for wear.

Adjusting the brake pedal free play

The brake pedal free play should measure 20.0–
30.0 mm (0.79–1.18 in) as shown. If the free play
is incorrect, adjust it as follows.

1. Fully loosen the brake lever free play adjust-

ing nut on the brake cable at the rear wheel
hub.

2. Turn the brake pedal free play adjusting nut

on the brake cable at the rear wheel hub in di-
rection (a) to increase the free play, and in di-
rection (b) to decrease it.

1. Brake pedal free play

U5UH65E0.book  Page 30  Monday, June 16, 2008  10:34 AM

Summary of Contents for GRIZZLY 350 YFM35FGY











































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands