Yamaha GRIZZLY 350 YFM350AZ Page 88 Owner'S Manual Download | Manualshive

Page: 88 / 138

background image

8-9

8

EBU23080

Removing and installing the panel

The panel shown needs to be removed to perform
some of the maintenance jobs described in this
chapter. Refer to this section each time the panel
needs to be removed and installed.

EBU23112

Panel A

To remove the panel
Remove the bolt, and then take the panel off.

To install the panel
Place the panel in the original position and install
the bolt.

NOTICE:

When installing the panel, be

sure not to pinch the cables or wires.

[ECB00381]

EBU23213

Checking the spark plug

The spark plug is an important engine component,
which is easy to check. Since heat and deposits
will cause any spark plug to slowly erode, the spark
plug should be removed and checked in accor-

1. Panel A

1. Panel A
2. Bolt

U5WH66E0.book Page 9 Thursday, June 18, 2009 10:41 AM

«
...
86
87
88
89
90
...
»

Summary of Contents for GRIZZLY 350 YFM350AZ











































































































































Reviews:

No comments

Related manuals for GRIZZLY 350 YFM350AZ

2005 TRX400EX Sportrax 400EX

Brand: Honda Pages: 238

LYNX RADIEN UTILITY ACE 2022 Series

Brand: BRP Pages: 252

Brand: Coleman Pages: 12

Brand: Can-Am Pages: 401

Brand: gio Pages: 22

Brand: PRONAR Pages: 136

K2 QUAD 250 - SERVICE

Brand: GAS GAS Pages: 64

Brand: Unimog Pages: 292

Sno Pro 120 2013

Brand: Arctic Cat Pages: 61

PROWLER XT 2014

Brand: Arctic Cat Pages: 218

Brand: Cushman Pages: 176

Brand: Yamaha Pages: 354

KTR-150 Go Kart

Brand: Roketa Pages: 8

Brand: Pow’R’kraft Pages: 16

Indy 340 Deluxe 2000

Brand: Polaris Pages: 52

2012 RANGER RZR 570

Brand: Polaris Pages: 403

Brand: Winway Pages: 67

ALTERRA MUD PRO 700 LTD EPS 2018

Brand: Textron Pages: 76

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands