Yamaha GRIZZLY 350 YFM350AZ Owner'S Manual Download | Manualshive

Page: 30 / 138

background image

4-5

4

EBU18323

Speed limiter

Your ATV is equipped with an adjustable speed
limiter. The speed limiter keeps the throttle from
fully opening, even when the throttle lever is
pushed to the maximum.

1. Loosen the locknut.
2. To increase the maximum engine power avail-

able and the maximum speed of the ATV, turn
the adjusting screw in direction (a). To de-
crease the maximum engine power available
and the maximum speed of the ATV, turn the
adjusting screw in direction (b). Do not turn
the adjusting screw out more than 12 mm
(0.47 in) or the throttle cable could be dam-
aged. Always make sure the throttle lever free
play is adjusted to 3.0–5.0 mm (0.12–0.20 in).
(See page 8-25.)

WARNING! Improper ad-

justment of the speed limiter and throttle
could cause throttle cable damage or im-
proper throttle operation. You could lose
control, resulting in an accident.

[EWB00241]

3. Tighten the locknut.

EBU18391

Front brake lever

The front brake lever is located on the right handle-
bar. To apply the front brake, pull the brake lever
toward the handlebar grip.

1. Locknut
2. Adjusting screw

3. No more than 12 mm (0.47 in)

U5WH66E0.book Page 5 Thursday, June 18, 2009 10:41 AM

«
...
28
29
30
31
32
...
»

Summary of Contents for GRIZZLY 350 YFM350AZ











































































































































Reviews:

No comments

Related manuals for GRIZZLY 350 YFM350AZ

Brand: Ezgo Pages: 102

Brand: Flagro Pages: 29

Brand: intrepid Pages: 54

Superlift Advantage Operators

Brand: Genie Pages: 28

Brand: LONCIN Pages: 65

Brand: Meec tools Pages: 35

2012 700 i Cruiser

Brand: Arctic Cat Pages: 708

Brand: NorAM Pages: 118

Sportsman 850 2021

Brand: Polaris Pages: 180

Brand: QERIDOO Pages: 36

RANGER Diesel 2013

Brand: Polaris Pages: 97

Brand: Polaris Pages: 141

Brand: E-Z-GO Pages: 180

Brand: BAIC Pages: 254

Brand: Taylor-Dunn Pages: 362

Brand: Baja motorsports Pages: 55

Brand: Taylor-Dunn Pages: 240

Brand: Eager Beaver Pages: 59

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands