Yamaha GRIZZLY 350 YFM350AZ Page 37 Owner'S Manual Download | Manualshive

Page: 37 / 138

background image

4-12

4

RES

This indicates reserve. With the fuel cock lever in
this position, the fuel reserve is made available.
Turn the fuel cock lever to this position if you run
out of fuel while riding. When this occurs, refuel as
soon as possible and be sure to turn the fuel cock
lever back to “ON”!

EBU18850

Starter (choke) “

”

Starting a cold engine requires a richer air-fuel mix-
ture, which is supplied by the starter (choke).
Move the starter (choke) in direction (a) to turn on
the starter (choke).

Move the starter (choke) in direction (b) to turn off
the starter (choke).
See the “Starting a cold engine” section on page
6-1 for proper operation.

EBU18881

Seat

To remove the seat

Pull the seat lock lever upward and pull up the seat
at the rear.

1. Arrow mark pointing to “RES”

1. Starter (choke) “

”

U5WH66E0.book Page 12 Thursday, June 18, 2009 10:41 AM

«
...
35
36
37
38
39
...
»

Summary of Contents for GRIZZLY 350 YFM350AZ











































































































































Reviews:

No comments

Related manuals for GRIZZLY 350 YFM350AZ

DOC ECO 30NXMOPRPB001

Brand: Nilox Pages: 84

Brand: Odes Industry Pages: 73

Brand: Skylift Pages: 407

Brand: Taylor-Dunn Pages: 132

Brand: B.O.B Pages: 36

Brand: LONCIN Pages: 56

Brand: Hsun Pages: 100

Brand: PRONAR Pages: 132

Brand: Landoll Pages: 70

Brand: Yamaha Pages: 172

Brand: Yamaha Pages: 150

Brand: KAYO MOTO Pages: 6

Brand: Yamaha Pages: 420

Brand: Yamaha Pages: 95

Brand: Polaris Pages: 4

Brand: Toro Pages: 40

Brand: Pulse Performance Products Pages: 15

Brand: Fisher-Price Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands