Yamaha GRIZZLY 350 YFM350AZ Page 108 Owner'S Manual Download | Manualshive

Page: 108 / 138

background image

8-29

8

have the oil seals of the brake master cylinder and
calipers as well as the brake hoses replaced at the
intervals listed below or whenever they are dam-
aged or leaking.

●

Oil seals: Replace every two years.

●

Brake hoses: Replace every four years.

EBU24394

Checking the front brake lever free play

The brake lever free play must be checked at the
intervals specified in the periodic maintenance and
lubrication chart. The brake lever should have no
free play as shown. If there is free play, have a
Yamaha dealer check the brake system.

EBU24514

Adjusting the brake pedal and rear
brake lever free play and checking the
brake pedal position

The brake pedal and brake lever free play must be
checked and, if necessary, adjusted at the inter-
vals specified in the periodic maintenance and lu-
brication chart.

TIP

●

Always perform this maintenance completely in
the following order whenever adjusting the rear
brake.

●

Before adjusting the brake lever and brake pedal
free play, check the rear brake shoes for wear.

Adjusting the brake pedal free play

The brake pedal free play should measure 20.0–
30.0 mm (0.79–1.18 in) as shown. If the free play
is incorrect, adjust it as follows.

1. No brake lever free play

U5WH66E0.book Page 29 Thursday, June 18, 2009 10:41 AM

«
...
106
107
108
109
110
...
»

Summary of Contents for GRIZZLY 350 YFM350AZ











































































































































Reviews:

No comments

Related manuals for GRIZZLY 350 YFM350AZ

Brand: Lynx Pages: 75

Brand: TATA Motors Pages: 180

Brand: HOMCOM Pages: 35

Brand: Kinroad Pages: 37

No Limit SL50 Compact

Brand: MGI Pages: 15

Brand: GMX Pages: 21

Brand: GMX Pages: 25

Brand: Ifor Williams Trailers Pages: 55

Brand: E-TON Pages: 225

Brand: KAYO MOTO Pages: 6

Brand: Metal-Fach Pages: 32

Brand: Metal-Fach Pages: 60

Brand: Suzuki Pages: 26

Brand: Ultraflex Pages: 22

Brand: Thump Pages: 78

Brand: Travel Lite Pages: 33

Brand: PLAYKIN Pages: 70

Brand: pronovost Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands