Yamaha GRIZZLY 350 YFM350AA Owner'S Manual Download | Manualshive

Page: 32 / 136

background image

4-7

4

EBU18460

Parking brake

Use the parking brake before starting the engine or
parking the ATV, especially on a slope. Apply the
rear brake lever and push down the lock plate to
apply the parking brake. Squeeze the rear brake
lever to release the parking brake.

WARNING

EWB00220

●

Always set the parking brake before starting
the engine. The ATV could start moving un-
expectedly if the parking brake is not ap-
plied. This could cause loss of control or a
collision.

●

Always be sure you have released the park-
ing brake before you begin to ride. The brake
could overheat if you ride the ATV without re-
leasing the parking brake. You could lose
braking performance which could cause an
accident. You could also wear out the brakes
prematurely.

EBU18581

Drive select lever

The drive select lever is used to shift your ATV into
the forward, neutral and reverse positions. See the
“Operating the drive select lever and driving in re-
verse” section on page 6-3 for the drive select lever
operation.

1. Parking brake lock plate

U5WH67E0.book Page 7 Thursday, June 3, 2010 2:10 PM

«
...
30
31
32
33
34
...
»

Summary of Contents for GRIZZLY 350 YFM350AA









































































































































Reviews:

No comments

Related manuals for GRIZZLY 350 YFM350AA

Brand: TYPHOON Pages: 28

Brand: Honda Pages: 84

Brand: Taylor-Dunn Pages: 111

Brand: FEATHERLITE TRAILERS Pages: 78

Brand: UtilityDump Pages: 13

Sportsman 9921792

Brand: Polaris Pages: 131

Raider-Classic 150

Brand: Dazon Pages: 79

2012 700 i Cruiser

Brand: Arctic Cat Pages: 708

Brand: Mi-T-M Pages: 65

Stockchaser IS12 2017

Brand: Columbia Pages: 36

Summit SU5-L-2 2017

Brand: Columbia Pages: 40

Brand: Humbaur Pages: 200

Brand: Landoll Pages: 36

BIG BEAR 4X4 YFM400FWNM

Brand: Yamaha Pages: 167

POWERSPORTS FR5DGK

Brand: MotoTec Pages: 32

Brand: Access Motor Pages: 65

2015 WILDCAT SPORT

Brand: Arctic Cat Pages: 68

Brand: Arctic Cat Pages: 84

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands