Yamaha GRIZZLY 350 YFM350AA Owner'S Manual Download

Page: 131 / 136

11-1

EBU26000

CONSUMER INFORMATION

EBU28200

Identification numbers

Record the vehicle identification number and mod-
el label information in the spaces provided below
for assistance when ordering spare parts from a
Yamaha dealer or for reference in case the ATV is
stolen.
VEHICLE IDENTIFICATION NUMBER:

MODEL LABEL INFORMATION:

EBU26041

Vehicle identification number

The vehicle identification number is stamped into
the frame.

The year of manufacture is listed in the vehicle
identification number as shown in the illustration.

1. Vehicle identification number (front left side)

U5WH67E0.book Page 1 Thursday, June 3, 2010 2:10 PM

Summary of Contents for GRIZZLY 350 YFM350AA









































































































































Search results

Summary of Contents for GRIZZLY 350 YFM350AA

Reviews:

Related manuals for GRIZZLY 350 YFM350AA

Brands by name

Popular brands

Yamaha GRIZZLY 350 YFM350AA, Owner'S Manual

Search results

Summary of Contents for GRIZZLY 350 YFM350AA

Reviews:

Related manuals for GRIZZLY 350 YFM350AA

Brands by name

Popular brands