Yamaha GRIZZLY 350 YFM350AA Owner'S Manual Download | Manualshive

Page: 107 / 136

background image

8-29

8

have the oil seals of the brake master cylinder and
calipers as well as the brake hoses replaced at the
intervals listed below or whenever they are dam-
aged or leaking.

●

Oil seals: Replace every two years.

●

Brake hoses: Replace every four years.

EBU24394

Checking the front brake lever free play

The brake lever free play must be checked at the
intervals specified in the periodic maintenance and
lubrication chart. The brake lever should have no
free play as shown. If there is free play, have a
Yamaha dealer check the brake system.

EBU24517

Adjusting the brake pedal and rear
brake lever free play and checking the
brake pedal height

The brake pedal and brake lever free play must be
checked and, if necessary, adjusted at the inter-
vals specified in the periodic maintenance and lu-
brication chart.

TIP

●

Always perform this maintenance completely in
the following order whenever adjusting the rear
brake.

●

Before adjusting the brake lever and brake pedal
free play, check the rear brake shoes for wear.

1.

Adjusting the brake pedal free play

The brake pedal free play should measure
20.0–30.0 mm (0.79–1.18 in) as shown. If the
free play is incorrect, adjust it as follows.

1. No brake lever free play

U5WH67E0.book Page 29 Thursday, June 3, 2010 2:10 PM

«
...
105
106
107
108
109
...
»

Summary of Contents for GRIZZLY 350 YFM350AA









































































































































Reviews:

No comments

Related manuals for GRIZZLY 350 YFM350AA

Brand: J&M Pages: 26

Brand: Polaris Pages: 174

Brand: LAMAX Pages: 150

Brand: Taylor-Dunn Pages: 186

Brand: Taylor-Dunn Pages: 240

Power Wheels B9273

Brand: Fisher-Price Pages: 44

Brand: E-Z-GO Pages: 192

Brand: E-Z-GO Pages: 84

Brand: VARES Pages: 44

Brand: KAYO MOTOR Pages: 96

Brand: Rato Pages: 118

GRIZZLY 700 2013

Brand: Yamaha Pages: 174

Brand: Yamaha Pages: 122

Brand: Yamaha Pages: 431

Brand: Yamaha Pages: 156

Brand: Warn Pages: 4

Brand: Suzuki Pages: 50

Brand: SeaCom Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands