Yamaha GP800R WaveRunner 2003 Service Manual Download Page 222

Page: 222 / 247

8-31

HULL

HOOD

HOSES

EXPLODED DIAGRAM

REMOVAL AND INSTALLATION CHART

Step

Procedure/Part name

Q’ty

Service points

HOSES REMOVAL

Follow the left “Step” for removal.

Engine unit

Refer to “ENGINE UNIT” in chapter 5.

Steering console cover assembly

Refer to “STEERING CONSOLE COVER”.

Band

Ventilation hose (stern side)

NOTE:

●

Route the ventilation hose (bow side) in
front of the fuel level sensor lead.

●

Route the ventilation hose (stern side)
front the oil level sensor lead and the oil
tank breather hose.

Ventilation hose (bow side)

Summary of Contents for GP800R WaveRunner 2003
























































































































































































































































Search results

Summary of Contents for GP800R WaveRunner 2003

Reviews:

Related manuals for GP800R WaveRunner 2003

Brands by name

Popular brands

Yamaha GP800R WaveRunner 2003, Service Manual

Search results

Summary of Contents for GP800R WaveRunner 2003

Reviews:

Related manuals for GP800R WaveRunner 2003

Brands by name

Popular brands