background image

OPERATION AND IMPORTANT RIDING POINTS

6-4

6

EAU16841

Engine break-in 

There is never a more important period
in the life of your engine than the period
between 0 and 1600 km (1000 mi). For
this reason, you should read the follow-
ing material carefully.
Since the engine is brand new, do not
put an excessive load on it for the first
1600 km (1000 mi). The various parts in
the engine wear and polish themselves
to the correct operating clearances.
During this period, prolonged full-throt-
tle operation or any condition that might
result in engine overheating must be
avoided.

EAU17092

0–1000 km (0–600 mi)

Avoid prolonged operation above 6000
r/min. 

NOTICE:

 After 1000 km (600

mi) of operation, the engine oil must
be changed and the oil filter car-
tridge or element replaced.

 [ECA10302]

1000–1600 km (600–1000 mi)

Avoid prolonged operation above 7200
r/min.

1600 km (1000 mi) and beyond

The vehicle can now be operated nor-
mally.

NOTICE

ECA10310

Keep the engine speed out of
the tachometer red zone.

If any engine trouble should oc-
cur during the engine break-in
period, immediately have a
Yamaha dealer check the vehi-
cle.

EAU17213

Parking 

When parking, stop the engine, and
then remove the key from the main
switch.

WARNING

EWA10311

Since the engine and exhaust
system can become very hot,
park in a place where pedestri-
ans or children are not likely to
touch them and be burned.

Do not park on a slope or on soft
ground, otherwise the vehicle
may overturn, increasing the
risk of a fuel leak and fire.

Do not park near grass or other
flammable materials which
might catch fire.

U3C313E0.book  Page 4  Monday, August 18, 2008  2:18 PM

Summary of Contents for FZS10Y











































































































Reviews: