manualshive.com logo in svg

Yamaha FZS10A, Owner'S Manual, Page: 66 / 112

Share
Download
Yamaha FZS10A Owner'S Manual Download Page 66

PERIODIC MAINTENANCE AND ADJUSTMENT

7-17

7

hose and the fuel tank overflow
hose in the original position.

WARNING! Before placing the
fuel tank in the original position,
make sure that the fuel hoses
are not damaged. If any fuel
hose is damaged, do not start
the engine but have a Yamaha
dealer replace the hose, other-
wise fuel may leak, creating a
fire hazard.

 [EWA11361]

11. Install the fuel tank bolts.
12. Place the fuel tank cowling in the

original position, and then install
the fuel tank cowling bolts.

13. Install the panels.
14. Install the rider seat.

EAU44734

Checking the engine idling 
speed 

Check the engine idling speed and, if
necessary, have it corrected by a
Yamaha dealer.

1. Fuel tank breather hose (except for Califor-

nia)

2. Original position (paint mark)

3. Fuel tank overflow hose

3

2

1

Engine idling speed:

1100–1300 r/min

U1CA11E0.book  Page 17  Thursday, September 23, 2010  11:51 AM

Summary of Contents for FZS10A

















































































































Reviews:

No comments