Yamaha FZS10A Page 87 Owner'S Manual Download

Page: 87 / 112

PERIODIC MAINTENANCE AND ADJUSTMENT

7-38

EAU25080

Rear wheel

EAU40022

To remove the rear wheel

WARNING

EWA10821

To avoid injury, securely support the
vehicle so there is no danger of it
falling over.

1. Loosen the axle nut.

2. Place the vehicle on the center-

stand.

3. Remove the axle nut.
4. Loosen the locknut on each side of

the swingarm.

5. Turn the drive chain slack adjust-

ing bolts fully in direction (a) and
push the wheel forward.

6. Remove the drive chain from the

rear sprocket.

TIP

●

If the drive chain is difficult to re-
move, remove the wheel axle first,
and then lift the wheel upward
enough to remove the drive chain
from the rear sprocket.

●

The drive chain cannot be disas-
sembled.

7. While supporting the brake caliper

bracket, pull the wheel axle out,
and then remove the wheel.

NOTICE:

Do not apply the brake

after the wheel has been re-
moved together with the brake
disc, otherwise the brake pads
will be forced shut.

[ECA11071]

EAU48402

To install the rear wheel

1. Install the wheel and the brake cal-

iper bracket by inserting the wheel
axle from the left-hand side.

TIP

●

Make sure that the slot in the brake
caliper bracket is fit over the retain-
er on the swingarm.

●

Make sure that there is enough
space between the brake pads be-
fore installing the wheel.

1. Axle nut

2. Brake caliper bracket
3. Brake caliper

1. Drive chain slack adjusting bolt
2. Locknut

(a)

1. Wheel axle

U1CA11E0.book Page 38 Thursday, September 23, 2010 11:51 AM

Summary of Contents for FZS10A

















































































































Search results

Summary of Contents for FZS10A

Reviews:

Related manuals for FZS10A

Brands by name

Popular brands

Yamaha FZS10A, Owner'S Manual

Search results

Summary of Contents for FZS10A

Reviews:

Related manuals for FZS10A

Brands by name

Popular brands