Yamaha FZS10A Page 37 Owner'S Manual Download | Manualshive

Page: 37 / 112

background image

INSTRUMENT AND CONTROL FUNCTIONS

4-18

4

Compression damping force

The compression damping force is ad-
justed on the left front fork leg only. To
increase the compression damping
force and thereby harden the compres-
sion damping, turn the adjusting screw
in direction (a). To decrease the com-

pression damping force and thereby
soften the compression damping, turn
the adjusting screw in direction (b).

TIP

Be sure to perform this adjustment on
the left front fork leg.

TIP

Although the total number of clicks of a
damping force adjusting mechanism
may not exactly match the above spec-
ifications due to small differences in
production, the actual number of clicks
always represents the entire adjusting
range. To obtain a precise adjustment,
it would be advisable to check the num-
ber of clicks of each damping force ad-
justing mechanism and to modify the
specifications as necessary.

1. Rebound damping force adjusting screw

Rebound damping setting:

Minimum (soft):

26 click(s) in direction (b)*

Standard:

18 click(s) in direction (b)*

Maximum (hard):

1 click(s) in direction (b)*

* With the adjusting screw fully turned

in direction (a)

1. Compression damping force adjusting screw

Compression damping setting:

Minimum (soft):

26 click(s) in direction (b)*

Standard:

5 click(s) in direction (b)*

Maximum (hard):

1 click(s) in direction (b)*

* With the adjusting screw fully turned

in direction (a)

U1CA11E0.book Page 18 Thursday, September 23, 2010 11:51 AM

«
...
35
36
37
38
39
...
»

Summary of Contents for FZS10A

















































































































Reviews:

No comments

Related manuals for FZS10A

Brand: GAS GAS Pages: 56

Powersports CT200U

Brand: Coleman Pages: 37

Brand: APRILIA Pages: 9

Brand: Honda Pages: 325

Brand: GAS GAS Pages: 107

640 LC4 Adventure

Brand: KTM Pages: 59

Brand: Sundstrom Pages: 68

Brand: Memphis Shades Pages: 2

Brand: Razor Pages: 3

Brand: Arai Helmet Pages: 52

Brand: Arai Helmet Pages: 60

2004 Moto Matrix

Brand: Yamaha Pages: 41

Brand: Yamaha Pages: 48

Brand: Yamaha Pages: 28

2004 FJR1300(S)

Brand: Yamaha Pages: 44

Brand: Yamaha Pages: 30

Brand: Yamaha Pages: 87

Brand: Yamaha Pages: 84

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands