Yamaha FZS10A Page 3 Owner'S Manual Download | Manualshive

Page: 3 / 112

background image

INTRODUCTION

EAU10083

Congratulations on your purchase of the Yamaha FZS10A(C). This model is the result of Yamaha’s vast experience in the
production of fine sporting, touring, and pacesetting racing machines. It represents the high degree of craftsmanship and
reliability that have made Yamaha a leader in these fields.
This manual will give you an understanding of the operation, inspection, and basic maintenance of this motorcycle. If you
have any questions concerning the operation or maintenance of your motorcycle, please consult a Yamaha dealer.
The design and manufacture of this Yamaha motorcycle fully comply with the emissions standards for clean air applicable at
the date of manufacture. Yamaha has met these standards without reducing the performance or economy of operation of the
motorcycle. To maintain these high standards, it is important that you and your Yamaha dealer pay close attention to the
recommended maintenance schedules and operating instructions contained within this manual.
Yamaha continually seeks advancements in product design and quality. Therefore, while this manual contains the most cur-
rent product information available at the time of printing, there may be minor discrepancies between your motorcycle and this
manual. If there is any question concerning this manual, please consult a Yamaha dealer.

WARNING

EWA10011

Please read this manual and the “YOU AND YOUR MOTORCYCLE: RIDING TIPS” booklet carefully before operating
this motorcycle. Do not attempt to operate this motorcycle until you have attained adequate knowledge of its con-
trols and operating features. Regular inspections and careful maintenance, along with good operating techniques,
will help ensure that you safely enjoy the capabilities and reliability of this motorcycle.

U1CA11E0.book Page 1 Thursday, September 23, 2010 11:51 AM

«
1
2
3
4
5
...
»

Summary of Contents for FZS10A

















































































































Reviews:

No comments

Related manuals for FZS10A

Brand: HYOSUNG Pages: 98

Brand: GIVI Pages: 3

Brand: R&G Pages: 8

Brand: KTM Pages: 130

Brand: R&G Pages: 24

Brand: Sicor Pages: 2

Light Bee QL3000DY

Brand: Surron Pages: 18

Brand: TVS Pages: 60

Brand: Baja motorsports Pages: 66

Brand: yasuni Pages: 8

Brand: KREIDLER Pages: 4

Brand: DYNATEK Pages: 6

Brand: Twiins Pages: 40

ES350 BURROeSCOOTER

Brand: Burro Max Pages: 32

Brand: R&G Pages: 2

Brand: R&G Pages: 2

Brand: R&G Pages: 4

Brand: R&G Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands