Yamaha FZS10A Page 21 Owner'S Manual Download | Manualshive

Page: 21 / 112

background image

INSTRUMENT AND CONTROL FUNCTIONS

4-2

4

To unlock the steering

Push the key in, and then turn it to
“OFF” while still pushing it.

EAU49391

Indicator lights and warning
lights

EAU11030

Turn signal indicator lights “

”

and “

”

The corresponding indicator light flash-
es when the turn signal switch is
pushed to the left or right.

EAU11060

Neutral indicator light “

”

This indicator light comes on when the
transmission is in the neutral position.

EAU11080

High beam indicator light “

”

This indicator light comes on when the
high beam of the headlight is switched
on.

EAU11254

Oil level warning light “

”

This warning light comes on if the en-
gine oil level is low.
The electrical circuit of the warning light
can be checked by turning the key to
“ON”. The warning light should come
on for a few seconds, and then go off.
If the warning light does not come on
initially when the key is turned to “ON”,
or if the warning light remains on, have
a Yamaha dealer check the electrical
circuit.

TIP

●

Even if the oil level is sufficient, the
warning light may flicker when
riding on a slope or during sudden
acceleration or deceleration, but
this is not a malfunction.

1. Push.
2. Turn.

1

2

1. Left turn signal indicator light “

”

2. Right turn signal indicator light “

”

3. Neutral indicator light “

”

4. High beam indicator light “

”

5. Engine trouble warning light “

”

6. Oil level warning light “

”

7. Coolant temperature warning light “

”

U1CA11E0.book Page 2 Thursday, September 23, 2010 11:51 AM

«
...
19
20
21
22
23
...
»

Summary of Contents for FZS10A

















































































































Reviews:

No comments

Related manuals for FZS10A

Brand: yasuni Pages: 11

Brand: Öhlins Pages: 2

Brand: KTM Pages: 38

Brand: AMFD Pages: 17

Brand: R&G Pages: 2

Brand: Honda Pages: 130

Brand: GAS GAS Pages: 69

TXT PRO - PART LIST 2005

Brand: GAS GAS Pages: 38

Super Tenere XTZ1200Z

Brand: Yamaha Pages: 108

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 351

Brand: Yamaha Pages: 96

Brand: Bajaj Pages: 44

Brand: Eastwood Pages: 8

Brand: JIMS Pages: 2

Brand: Dräger Pages: 164

Brand: IL Motorsport Pages: 2

Brand: HYOSUNG Pages: 100

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands