Yamaha FZ8NB Owner'S Manual Download

Page: 83 / 108

PERIODIC MAINTENANCE AND ADJUSTMENT

7-39

5. Pull the wheel axle out, and then

remove the wheel.

EAU49841

To install the front wheel

1. Lift the wheel up between the fork

legs.

2. Insert the wheel axle.
3. Lower the front wheel so that it is

on the ground, and then put the
sidestand down.

4. Install the brake calipers (together

with the reflectors) by installing the
bolts.

TIP

Make sure that there is enough space
between the brake pads before install-
ing the brake calipers onto the brake
discs.

5. Install the brake hose holders by

installing the bolt and nut.

6. Tighten the brake caliper bolts to

the specified torque.

7. Tighten the wheel axle, and then

the wheel axle pinch bolt to their
specified torque.

8. Push down hard on the handlebar

several times to check for proper
fork operation.

EAU25080

Rear wheel

EAU25314

To remove the rear wheel

WARNING

EWA10821

To avoid injury, securely support the
vehicle so there is no danger of it
falling over.

1. Loosen the axle nut.

2. Lift the rear wheel off the ground

according to the procedure on
page 7-37.

3. Remove the axle nut.
4. Fully loosen the locknut on each

side of the swingarm.

1. Brake caliper bolt
2. Brake caliper

3. Reflector

Tightening torque:

Brake caliper bolt:

40 Nm (4.0 m·kgf, 29 ft·lbf)

Tightening torques:

Wheel axle:

65 Nm (6.5 m·kgf, 47 ft·lbf)

Front wheel axle pinch bolt:

23 Nm (2.3 m·kgf, 17 ft·lbf)

1. Axle nut

U39P11E0.book Page 39 Monday, August 1, 2011 5:00 PM

Summary of Contents for FZ8NB













































































































Search results

Summary of Contents for FZ8NB

Reviews:

Related manuals for FZ8NB

Brands by name

Popular brands

Yamaha FZ8NB, Owner'S Manual

Search results

Summary of Contents for FZ8NB

Reviews:

Related manuals for FZ8NB

Brands by name

Popular brands