Yamaha FZ8 Owner'S Manual Download

Page: 82 / 108

PERIODIC MAINTENANCE AND ADJUSTMENT

7-39

TIP

Make sure that there is enough space
between the brake pads before install-
ing the brake calipers onto the brake
discs.

5. Install the brake hose holders by

installing the bolt and nut.

6. Tighten the brake caliper bolts to

the specified torque.

7. Tighten the wheel axle, and then

the wheel axle pinch bolt to their
specified torque.

8. Push down hard on the handlebar

several times to check for proper
fork operation.

EAU25080

Rear wheel

EAU25314

To remove the rear wheel

WARNING

EWA10821

To avoid injury, securely support the
vehicle so there is no danger of it
falling over.

1. Loosen the axle nut.

2. Lift the rear wheel off the ground

according to the procedure on
page 7-37.

3. Remove the axle nut.
4. Fully loosen the locknut on each

side of the swingarm.

5. Turn the drive chain slack adjust-

ing bolts fully in direction (a) and
push the wheel forward.

6. Remove the drive chain from the

rear sprocket.

TIP

●

If the drive chain is difficult to re-
move, remove the wheel axle first,
and then lift the wheel upward
enough to remove the drive chain
from the rear sprocket.

●

The drive chain cannot be disas-
sembled.

7. While supporting the brake caliper

bracket, pull the wheel axle out,
and then remove the wheel.

Tightening torque:

Brake caliper bolt:

40 Nm (4.0 m·kgf, 29 ft·lbf)

Tightening torques:

Wheel axle:

65 Nm (6.5 m·kgf, 47 ft·lbf)

Front wheel axle pinch bolt:

23 Nm (2.3 m·kgf, 17 ft·lbf)

1. Axle nut

1. Drive chain slack adjusting bolt
2. Locknut

(a)

U39P10E0.book Page 39 Thursday, October 7, 2010 5:12 PM

Summary of Contents for FZ8













































































































Search results

Summary of Contents for FZ8

Reviews:

Related manuals for FZ8

Brands by name

Popular brands

Yamaha FZ8, Owner'S Manual

Search results

Summary of Contents for FZ8

Reviews:

Related manuals for FZ8

Brands by name

Popular brands