Yamaha FZ8 Owner'S Manual Download | Manualshive

Page: 65 / 108

background image

PERIODIC MAINTENANCE AND ADJUSTMENT

7-22

7

braking performance, which may re-
sult in loss of control and an acci-
dent.

EAU22273

Brake light switches

The brake light, which is activated by
the brake pedal and brake lever, should
come on just before braking takes ef-
fect. If necessary, adjust the rear brake
light switch as follows, but the front
brake light switch should be adjusted
by a Yamaha dealer.
Turn the rear brake light switch adjust-
ing nut while holding the rear brake light
switch in place. To make the brake light
come on earlier, turn the adjusting nut
in direction (a). To make the brake light
come on later, turn the adjusting nut in
direction (b).

EAU22392

Checking the front and rear
brake pads

The front and rear brake pads must be
checked for wear at the intervals spec-
ified in the periodic maintenance and
lubrication chart.

EAU36890

Front brake pads

Each front brake pad is provided with
wear indicators, which allows you to
check the brake pad wear without hav-
ing to disassemble the brake. To check
the brake pad wear, check the position
of the wear indicators while applying
the brake. If a brake pad has worn to

1. Rear brake light switch

2. Rear brake light switch adjusting nut

1

2

(b)

(a)

1. Brake pad wear indicator

1

1

U39P10E0.book Page 22 Thursday, October 7, 2010 5:12 PM

«
...
63
64
65
66
67
...
»

Summary of Contents for FZ8













































































































Reviews:

No comments

Related manuals for FZ8

Brand: Yamaha Pages: 88

Brand: Gentex Pages: 15

Brand: Artotic Pages: 9

Brand: yasuni Pages: 9

Brand: MOTO GUZZI Pages: 134

Brand: DYNATEK Pages: 3

Brand: DYNATEK Pages: 6

Brand: RS Motorcycle Solutions Pages: 2

Brand: Athena Pages: 88

Brand: R&G Pages: 2

Brand: ChatterBox Pages: 10

Brand: Wunderkind Custom Pages: 4

WIN'ZIP 7701ZIP

Brand: Bagster Pages: 2

Brand: Malaguti Pages: 42

Brand: Malaguti Pages: 80

Brand: Royal Enfield Pages: 214

Brand: Baja Pages: 8

Brand: R&G Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands