Yamaha FZ8 Owner'S Manual Download | Manualshive

Page: 27 / 108

background image

INSTRUMENT AND CONTROL FUNCTIONS

4-10

4

EAU26823

Brake lever

The brake lever is located at the right
handlebar grip. To apply the front
brake, pull the lever toward the handle-
bar grip.

The brake lever is equipped with a
brake lever position adjusting dial. To
adjust the distance between the brake
lever and the handlebar grip, turn the
adjusting dial while holding the lever
pushed away from the handlebar grip.
Make sure that the appropriate setting
on the adjusting dial is aligned with
the “

” mark on the brake lever.

EAU12941

Brake pedal

The brake pedal is on the right side of
the motorcycle. To apply the rear
brake, press down on the brake pedal.

EAU13074

Fuel tank cap

To open the fuel tank cap

Open the fuel tank cap lock cover, in-
sert the key into the lock, and then turn
it 1/4 turn clockwise. The lock will be re-
leased and the fuel tank cap can be
opened.

To close the fuel tank cap

1. Push the fuel tank cap into position

with the key inserted in the lock.

2. Turn the key counterclockwise to

the original position, remove it, and
then close the lock cover.

1. Brake lever

2. Distance between brake lever and handlebar

grip

3. Brake lever position adjusting dial
4. “

” mark

5

4

3

2

1

1

2

4

3

1. Brake pedal

1

1. Fuel tank cap lock cover

2. Unlock.

2

1

U39P10E0.book Page 10 Thursday, October 7, 2010 5:12 PM

«
...
25
26
27
28
29
...
»

Summary of Contents for FZ8













































































































Reviews:

No comments

Related manuals for FZ8

Brand: GIVI Pages: 3

Brand: R&G Pages: 6

Power Commander III 718-411

Brand: Dynojet Pages: 3

Brand: KTM Pages: 163

Brand: Zero Pages: 162

950 SUPER ENDURO R 2006

Brand: KTM Pages: 86

Brand: Cellularline Pages: 2

Brand: Suzuki Pages: 522

Brand: TVS Pages: 60

Brand: Baja motorsports Pages: 66

Brand: DYNATEK Pages: 1

Brand: Scott Pages: 22

Brand: SCORPION Pages: 2

Brand: SCORPION Pages: 15

Brand: Can-Am Pages: 195

Brand: Buell Pages: 4

Brand: Benelli Pages: 464

TORNADO NAKED TNT125

Brand: Benelli Pages: 530

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands