Yamaha FZ6-NSV Owner'S Manual Download Page 26 | Manualshive

Page: 26 / 90

background image

INSTRUMENT AND CONTROL FUNCTIONS

3-10

EAU12870

Shift pedal

The shift pedal is located on the left
side of the engine and is used in com-
bination with the clutch lever when
shifting the gears of the 6-speed con-
stant-mesh transmission equipped on
this motorcycle.

EAU26822

Brake lever

The brake lever is located at the right
handlebar grip. To apply the front
brake, pull the lever toward the handle-
bar grip.

The brake lever is equipped with a po-
sition adjusting dial. To adjust the dis-
tance between the brake lever and the
handlebar grip, turn the adjusting dial
while holding the lever pushed away
from the handlebar grip. Make sure that
the appropriate setting on the adjusting
dial is aligned with the “

” mark on the

brake lever.

EAU12941

Brake pedal

The brake pedal is on the right side of
the motorcycle. To apply the rear
brake, press down on the brake pedal.

1. Shift pedal

1. Brake lever

2. Brake lever position adjusting dial

3. “

” mark

4. Distance between brake lever and handlebar

grip

1. Brake pedal

U1B322E0.book Page 10 Monday, August 8, 2005 1:49 PM

ProCarManuals.com

«
...
24
25
26
27
28
...
»

Summary of Contents for FZ6-NSV



























































































Reviews:

No comments

Related manuals for FZ6-NSV

Brand: Bajaj Auto Pages: 38

Brand: Dakota Digital Pages: 6

Premium Motorcycle Cover

Brand: Velmia Pages: 32

Body Protector 4.5 Junior

Brand: Leatt Pages: 40

Brand: TB Pages: 8

Brand: Suzuki Pages: 447

Daytona 675 2014

Brand: Triumph Pages: 162

Brand: Honda Pages: 127

Brand: GYS Pages: 32

Brand: Yamaha Pages: 112

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 114

YZF-R1P 2001-2003

Brand: Yamaha Pages: 439

Brand: RIEJU Pages: 7

Brand: Rockford Fosgate Pages: 8

Brand: Rockford Fosgate Pages: 17

Brand: Vento Pages: 88

Brand: Beta Pages: 248

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands