Yamaha FZ6-N Owner'S Manual Download Page 71

Page: 71 / 88

PERIODIC MAINTENANCE AND MINOR REPAIR

6-33

EAU24860

To install the front wheel

1. Lift the wheel up between the fork

legs.

2. Insert the wheel axle.
3. Lower the front wheel so that it is

on the ground.

4. Install the brake calipers by install-

ing the bolts.

NOTE:

Make sure that there is enough space
between the brake pads before install-
ing the brake calipers onto the brake
discs.

5. Install the brake hose holders by

installing the bolts.

6. Tighten the wheel axle, the front

wheel axle pinch bolt and the
brake caliper bolts to the specified
torques.

7. Push down hard on the handlebar

several times to check for proper
fork operation.

EAU25080

Rear wheel

EAU34411

To remove the rear wheel

WARNING

EWA10820

●

It is advisable to have a Yamaha
dealer service the wheel.

●

Securely support the motor-
cycle so that there is no danger
of it falling over.

1. Loosen the axle nut.
2. Lift the rear wheel off the ground

according to the procedure on
page 6-31.

3. Remove the axle nut.
4. Loosen the locknut and drive chain

adjusting nut on each side of the
swingarm.

Tightening torques:

Wheel axle:

72 Nm (7.2 m·kgf, 52 ft·lbf)

Front wheel axle pinch bolt:

19 Nm (1.9 m·kgf, 14 ft·lbf)

Brake caliper bolt:

40 Nm (4.0 m·kgf, 29 ft·lbf)

U1B3E1E0.book Page 33 Thursday, July 8, 2004 11:49 AM

Summary of Contents for FZ6-N

























































































Search results

Summary of Contents for FZ6-N

Reviews:

Related manuals for FZ6-N

Brands by name

Popular brands

Yamaha FZ6-N, Owner'S Manual

Search results

Summary of Contents for FZ6-N

Reviews:

Related manuals for FZ6-N

Brands by name

Popular brands