Yamaha FZ6-N Owner'S Manual Download Page 63 | Manualshive

Page: 63 / 88

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-25

6

EAU23280

Checking the steering

Worn or loose steering bearings may
cause danger. Therefore, the operation
of the steering must be checked as fol-
lows at the intervals specified in the pe-
riodic maintenance and lubrication
chart.

1. Place a stand under the engine to

raise the front wheel off the
ground.

WARNING

EWA10750

Securely support the vehicle so that
there is no danger of it falling over.

2. Hold the lower ends of the front

fork legs and try to move them for-
ward and backward. If any free
play can be felt, have a Yamaha
dealer check or repair the steering.

EAU23290

Checking the wheel bearings

The front and rear wheel bearings must
be checked at the intervals specified in
the periodic maintenance and lubrica-
tion chart. If there is play in the wheel
hub or if the wheel does not turn
smoothly, have a Yamaha dealer check
the wheel bearings.

U1B3E1E0.book Page 25 Thursday, July 8, 2004 11:49 AM

«
...
61
62
63
64
65
...
»

Summary of Contents for FZ6-N

























































































Reviews:

No comments

Related manuals for FZ6-N

Brand: Maico Pages: 13

Brand: ICON Pages: 2

Power commander GSXR750

Brand: Dynojet Pages: 4

2016 Empulse TT

Brand: Victory Motorcycles Pages: 138

Brand: BMW Motorrad Pages: 231

Brand: Triumph Pages: 53

Brand: Cycle Protect Pages: 15

Brand: KTM Pages: 22

Brand: Blata Pages: 17

Brand: National Cycle Pages: 2

Brand: Öhlins Pages: 2

Brand: Aim Pages: 5

ZIEGER 10005243

Brand: IBEX Pages: 4

Brand: Xenith Pages: 7

Brand: HYOSUNG Pages: 100

Brand: HYOSUNG Pages: 96

rivercide 250 cc

Brand: Benelli Pages: 15

Brand: Benelli Pages: 72

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands