Yamaha FZ6-N Owner'S Manual Download Page 59 | Manualshive

Page: 59 / 88

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-21

6

EAU23021

Lubricating the drive chain

The drive chain must be cleaned and
lubricated at the intervals specified in
the periodic maintenance and lubrica-
tion chart, otherwise it will quickly wear
out, especially when riding in dusty or
wet areas. Service the drive chain as
follows.

CAUTION:

ECA10581

The drive chain must be lubricated
after washing the motorcycle and
riding in the rain.

1. Clean the drive chain with kero-

sene and a small soft brush.

CAUTION:

ECA11120

To prevent damaging the O-rings, do
not clean the drive chain with steam
cleaners, high-pressure washers or
inappropriate solvents.

2. Wipe the drive chain dry.
3. Thoroughly lubricate the drive

chain with a special O-ring chain
lubricant.

CAUTION:

ECA11110

Do not use engine oil or any other lu-
bricants for the drive chain, as they
may contain substances that could
damage the O-rings.

EAU23100

Checking and lubricating the
cables

The operation of all control cables and
the condition of the cables should be
checked before each ride, and the ca-
bles and cable ends should be lubricat-
ed if necessary. If a cable is damaged
or does not move smoothly, have a
Yamaha dealer check or replace it.

WARNING

EWA10720

Damage to the outer sheath may in-
terfere with proper cable operation
and will cause the inner cable to
rust. Replace a damaged cable as
soon as possible to prevent unsafe
conditions.

Recommended lubricant:

Engine oil

U1B3E1E0.book Page 21 Thursday, July 8, 2004 11:49 AM

«
...
57
58
59
60
61
...
»

Summary of Contents for FZ6-N

























































































Reviews:

No comments

Related manuals for FZ6-N

Brand: Palm Pages: 14

Brand: Dayi Motor Pages: 15

Brand: hepco & becker Pages: 4

Freeride 350 AUS

Brand: KTM Pages: 25

MILWAUKEE-EIGHT 5833

Brand: JIMS Pages: 10

Brand: Honda Pages: 190

Brand: IRC Pages: 2

Brand: Puch Pages: 151

Freeride 350 2013

Brand: KTM Pages: 113

Brand: X-lite Pages: 100

WOLVERINE X4 2021

Brand: Yamaha Pages: 192

Brand: Yamaha Pages: 224

Brand: Yamaha Pages: 343

Brand: Yamaha Pages: 404

Brand: Yamaha Pages: 432

Brand: Yamaha Pages: 404

Brand: Yamaha Pages: 694

Brand: Yamaha Pages: 864

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands