Yamaha FZ6-N Owner'S Manual Download Page 24 | Manualshive

Page: 24 / 88

background image

INSTRUMENT AND CONTROL FUNCTIONS

3-10

3

EAU12820

Clutch lever

The clutch lever is located at the left
handlebar grip. To disengage the
clutch, pull the lever toward the handle-
bar grip. To engage the clutch, release
the lever. The lever should be pulled
rapidly and released slowly for smooth
clutch operation.
The clutch lever is equipped with a
clutch switch, which is part of the igni-
tion circuit cut-off system. (See page
3-16.)

EAU12870

Shift pedal

The shift pedal is located on the left
side of the engine and is used in com-
bination with the clutch lever when
shifting the gears of the 6-speed con-
stant-mesh transmission equipped on
this motorcycle.

EAU26822

Brake lever

The brake lever is located at the right
handlebar grip. To apply the front
brake, pull the lever toward the handle-
bar grip.

The brake lever is equipped with a po-
sition adjusting dial. To adjust the dis-
tance between the brake lever and the
handlebar grip, turn the adjusting dial
while holding the lever pushed away
from the handlebar grip. Make sure that
the appropriate setting on the adjusting
dial is aligned with the “

” mark on the

brake lever.

1. Clutch lever

1. Shift pedal

1. Brake lever

2. Brake lever position adjusting dial

3. “

” mark

4. Distance between brake lever and handlebar

grip

U1B3E1E0.book Page 10 Thursday, July 8, 2004 11:49 AM

«
...
22
23
24
25
26
...
»

Summary of Contents for FZ6-N

























































































Reviews:

No comments

Related manuals for FZ6-N

Brand: DAELIM Pages: 2

Brand: N-Com Pages: 6

Mesh Helmet Cover

Brand: Ops-Core Pages: 2

Brand: Yamaha Pages: 108

Brand: Yamaha Pages: 118

Brand: Yamaha Pages: 110

Brand: Yamaha Pages: 120

Brand: Yamaha Pages: 216

Brand: Yamaha Pages: 380

Brand: Yamaha Pages: 658

Brand: Yamaha Pages: 106

Brand: Yamaha Pages: 90

Brand: Yamaha Pages: 509

Brand: Yamaha Pages: 508

Brand: Yamaha Pages: 510

Brand: Yamaha Pages: 578

Brand: Yamaha Pages: 610

Brand: Yamaha Pages: 610

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands