manualshive.com logo in svg

Yamaha FL200C, Owner'S Manual, Page: 50 / 100

Share
Download
Yamaha FL200C Owner'S Manual Download Page 50

Operation

44

EMU42561

Checking power trim and tilt system

WARNING

EWM01931

Never get under the lower unit while it is
tilted, even when the tilt support lever is
locked. Severe injury could occur if the
outboard motor accidentally falls.

Body parts can be crushed between the
motor and the clamp bracket when the
motor is trimmed or tilted.

Be sure no one is near the outboard mo-
tor before performing this check.

1.

Check the power trim and tilt unit for any
sign of oil leaks.

2.

Operate each of the power trim and tilt
switches on the remote control and en-
gine bottom cowling to check that all
switches work.

3.

Tilt the outboard motor up and check
that the tilt rod and trim rods are extend-
ed completely.

F200C, FL200C, F225B, FL225B

F225C

4.

Use the tilt support lever to lock the mo-
tor in the up position. Operate the tilt
down switch briefly so the motor is sup-
ported by the tilt support lever.

F200C, FL200C, F225B, FL225B

F225C

5.

Check that the tilt rod and trim rods are
free of corrosion or other flaws.

1. Tilt rod
2. Trim rods

1. Tilt rod
2. Trim rods

1. Tilt support lever

1. Tilt support lever

ZMU06016

1

2

ZMU06017

1

U6P27AE0.book  Page 44  Friday, December 6, 2013  6:17 PM

Summary of Contents for FL200C





































































































Reviews:

No comments