Yamaha FL115B Owner'S Manual Download

Page: 99 / 108

Trouble Recovery

A. Fill tank with clean, fresh fuel.

Q. Is spark plug gap incorrect?
A. Inspect and adjust as specified.

Q. Is ignition wiring damaged or poorly con-
nected?
A. Check wires for wear or breaks. Tighten all
loose connections. Replace worn or broken
wires.

Q. Have electrical parts failed?
A. Have serviced by a Yamaha dealer.

Q. Is specified fuel not being used?
A. Replace fuel with specified type.

Q. Is specified engine oil not being used?
A. Check and replace oil with specified type.

Q. Is thermostat faulty or clogged?
A. Have serviced by a Yamaha dealer.

Q. Is air vent screw closed?
A. Open the air vent screw.

Q. Is fuel pump damaged?
A. Have serviced by a Yamaha dealer.

Q. Is fuel joint connection incorrect?
A. Connect correctly.

Q. Is heat range of spark plug incorrect?
A. Inspect spark plug and replace it with rec-
ommended type.

Q. Is engine not responding properly to shift
lever position?
A. Have serviced by a Yamaha dealer.

Engine vibrates excessively.

Q. Is propeller damaged?
A. Have propeller repaired or replaced.

Q. Is propeller shaft damaged?
A. Have serviced by a Yamaha dealer.

Q. Are weeds or other foreign matter tangled
on propeller?
A. Remove and clean propeller.

Q. Is motor mounting bolt loose?
A. Tighten bolt.

Q. Is steering pivot loose or damaged?
A. Tighten or have serviced by a Yamaha
dealer.

EMU29434

Temporary action in emergen-

EMU29442

Impact damage

WARNING

EWM00871

The outboard motor can be seriously
damaged by a collision while operating or
trailering. Damage could make the out-
board motor unsafe to operate.

If the outboard motor hits an object in the wa-
ter, follow the procedure below.

Stop the engine immediately.

U6EK70E0.book Page 93 Friday, January 31, 2014 2:37 PM

Summary of Contents for FL115B













































































































Search results

Summary of Contents for FL115B

Reviews:

Related manuals for FL115B

Brands by name

Popular brands

Yamaha FL115B, Owner'S Manual

Search results

Summary of Contents for FL115B

Reviews:

Related manuals for FL115B

Brands by name

Popular brands