Yamaha FL115B Owner'S Manual Download Page 59

Page: 59 / 108

Operation

EMU40412

Outboard motor



Check that the outboard motor is mounted
properly and check the outboard motor
mounting bolts for looseness.



Check the propeller for damage.



Check for engine oil leaks.

EMU36494

Flushing device

Check that the flushing device’s garden hose
connector is securely screwed on to the fit-
ting on the bottom cowling.

NOTICE:

If the

garden hose connector is not properly
connected, cooling water can leak out and
the engine can overheat during operation.

[ECM01802]

EMU36965

Install cowling

Be sure that all cowling lock levers are
released.

Be sure that the rubber seal is seated all
the way around the top cowling.

Place the top cowling on the bottom
cowling.

Check to be sure the rubber seal is seat-
ed correctly between the top cowling
and the bottom cowling.

Move the cowling lock levers to lock the
top cowling as shown.

NOTICE:

If the

top cowling is not installed correctly,
water spray under the top cowling can
damage the engine, or the top cowling
can blow off at high speeds.

[ECM01992]

1. Oil dipstick
2. Upper mark
3. Lower mark

1. Fitting
2. Garden hose connector
3. Flushing device

ZMU08088

ZMU08089

1. Top cowling
2. Rubber seal

1. Cowling lock lever

ZMU08090

ZMU08091

U6EK70E0.book Page 53 Friday, January 31, 2014 2:37 PM

Summary of Contents for FL115B













































































































Search results

Summary of Contents for FL115B

Reviews:

Related manuals for FL115B

Brands by name

Popular brands

Yamaha FL115B, Owner'S Manual

Search results

Summary of Contents for FL115B

Reviews:

Related manuals for FL115B

Brands by name

Popular brands