Yamaha FJR1300S(C) Owner'S Manual Download Page 42

Page: 42 / 99

OPERATION AND IMPORTANT RIDING POINTS

5-4

CAUTION:

ECA10331

After 1000 km (600 mi) of operation,
the engine oil and final gear oil must
be changed, and the oil filter car-
tridge or element replaced.

1600 km (1000 mi) and beyond

The vehicle can now be operated nor-
mally.

CAUTION:

ECA10310

●

Keep the engine speed out of
the tachometer red zone.

●

If any engine trouble should oc-
cur during the engine break-in
period, immediately have a
Yamaha dealer check the vehi-
cle.

EAU17211

Parking

When parking, stop the engine, and
then remove the key from the main
switch.

WARNING

EWA10310

●

Since the engine and exhaust
system can become very hot,
park in a place where pedestri-
ans or children are not likely to
touch them.

●

Do not park on a slope or on soft
ground, otherwise the vehicle
may overturn.

CAUTION:

ECA10380

Never park in an area where there
are fire hazards such as grass or
other flammable materials.

5JW11.book Page 4 Friday, May 9, 2003 4:03 PM

Summary of Contents for FJR1300S(C)




































































































Search results

Summary of Contents for FJR1300S(C)

Reviews:

Related manuals for FJR1300S(C)

Brands by name

Popular brands

Yamaha FJR1300S(C), Owner'S Manual

Search results

Summary of Contents for FJR1300S(C)

Reviews:

Related manuals for FJR1300S(C)

Brands by name

Popular brands