Yamaha FJR1300S(C) Owner'S Manual Download Page 37 | Manualshive

Page: 37 / 99

background image

PRE-OPERATION CHECKS

4-2

4

EAU15601

Pre-operation check list

ITEM

CHECKS

PAGE

Fuel

• Check fuel level in fuel tank.
• Refuel if necessary.
• Check fuel line for leakage.

Engine oil

• Check oil level in engine.
• If necessary, add recommended oil to specified level.
• Check vehicle for oil leakage.

Final gear oil

• Check vehicle for oil leakage.

Coolant

• Check coolant level in reservoir.
• If necessary, add recommended coolant to specified level.
• Check cooling system for leakage.

Front brake

• Check operation.
• If soft or spongy, have Yamaha dealer bleed hydraulic system.
• Check brake pads for wear.
• Replace if necessary.
• Check fluid level in reservoir.
• If necessary, add recommended brake fluid to specified level.
• Check hydraulic system for leakage.

Rear brake

• Check operation.
• If soft or spongy, have Yamaha dealer bleed hydraulic system.
• Check brake pads for wear.
• Replace if necessary.
• Check fluid level in reservoir.
• If necessary, add recommended brake fluid to specified level.
• Check hydraulic system for leakage.

6-22, 6-23, 6-24

Clutch

• Check operation.
• If soft or spongy, have Yamaha dealer bleed hydraulic system.
• Check fluid level in reservoir.
• If necessary, add recommended fluid to specified level.
• Check hydraulic system for leakage.

5JW11.book Page 2 Friday, May 9, 2003 4:03 PM

«
...
35
36
37
38
39
...
»

Summary of Contents for FJR1300S(C)




































































































Reviews:

No comments

Related manuals for FJR1300S(C)

Brand: Kappa Pages: 4

Brand: Öhlins Pages: 2

STEADYSTAND Cross Basic

Brand: ACEBIKES Pages: 6

Brand: P.Lindberg Pages: 26

Brand: MadStad Engineering Pages: 8

SPORTTOURING ST4S

Brand: Ducati Pages: 313

Brand: Yamaha Pages: 119

Brand: Yamaha Pages: 124

Brand: Yamaha Pages: 360

Brand: Yamaha Pages: 580

Brand: Yamaha Pages: 98

Brand: Yamaha Pages: 80

Brand: Yamaha Pages: 86

Brand: Yamaha Pages: 90

Brand: Yamaha Pages: 88

Brand: Yamaha Pages: 92

Brand: Yamaha Pages: 388

Brand: Yamaha Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands