Yamaha FJR1300S(C) Owner'S Manual Download Page 29

Page: 29 / 99

INSTRUMENT AND CONTROL FUNCTIONS

3-12

2. Install the rider seat.

NOTE:

Make sure that the seats are properly
secured before riding.

EAU14461

Storage compartment

The storage compartment is located
under the passenger seat. (See page
3-11.)

WARNING

EWA10961

●

Do not exceed the load limit of 3
kg (7 lb) for the storage com-
partment.

●

Do not exceed the maximum
load of
FJR1300 200.0 kg (441 lb) (CAL)
FJR1300 201.0 kg (443 lb) (U49)
FJR1300A 193.0 kg (426 lb) (CAL)
FJR1300A 194.0 kg (428 lb) (U49)
for the vehicle.

EAU26881

Accessory box

The accessory box is located beside
the meter panel.

NOTE:

The accessory box can only be opened
when the key is turned to “ON” and the
transmission is in neutral.

CAUTION:

ECA11800

Do not place heat-sensitive items in
the accessory box. The accessory
box gets extremely hot especially
when the engine is running or is hot.

1. Receptacle
2. Seat holder

1. Storage compartment

1. Accessory box

5JW11.book Page 12 Friday, May 9, 2003 4:03 PM

Summary of Contents for FJR1300S(C)




































































































Search results

Summary of Contents for FJR1300S(C)

Reviews:

Related manuals for FJR1300S(C)

Brands by name

Popular brands

Yamaha FJR1300S(C), Owner'S Manual

Search results

Summary of Contents for FJR1300S(C)

Reviews:

Related manuals for FJR1300S(C)

Brands by name

Popular brands