Yamaha FJR1300S(C) Owner'S Manual Download Page 25 | Manualshive

Page: 25 / 99

background image

INSTRUMENT AND CONTROL FUNCTIONS

3-8

3

EAU12930

Brake lever

The brake lever is located at the right
handlebar grip. To apply the front
brake, pull the lever toward the handle-
bar grip.

The brake lever is equipped with a po-
sition adjusting dial. To adjust the dis-
tance between the brake lever and the
handlebar grip, turn the adjusting dial
while holding the lever pushed away
from the handlebar grip. Make sure that
the appropriate setting on the adjusting
dial is aligned with the arrow mark on
the brake lever.

EAU12941

Brake pedal

The brake pedal is on the right side of
the motorcycle. To apply the rear
brake, press down on the brake pedal.

EAU26791

ABS (For FJR1300A only)

The Yamaha ABS (Anti-lock Brake
System) features a dual electronic con-
trol system, which acts on the front and
rear brakes independently. The ABS is
monitored by an ECU (Electronic Con-
trol Unit), which will have recourse to
manual braking if a malfunction occurs.

WARNING

EWA10090

●

The ABS performs best on long
braking distances.

●

On certain (rough or gravel)
roads, the braking distance may
be longer with than without the
ABS. Therefore, always keep a
sufficient distance to the vehicle
ahead to match the riding
speed.

NOTE:

●

When the ABS is activated, the
brakes are operated in the usual
way. A pulsating action may be felt
at the brake lever or brake pedal,
but this does not indicate a mal-
function.

1. Brake lever

2. Arrow mark

3. Brake lever position adjusting dial
4. Distance between brake lever and handlebar

grip

1. Brake pedal

5JW11.book Page 8 Friday, May 9, 2003 4:03 PM

«
...
23
24
25
26
27
...
»

Summary of Contents for FJR1300S(C)




































































































Reviews:

No comments

Related manuals for FJR1300S(C)

Brand: Rally Pack Pages: 2

Brand: KYMCO Pages: 58

Brand: Yamaha Pages: 568

Brand: X-lite Pages: 76

Brand: R&G Pages: 6

Minirack 6602533 01 01

Brand: hepco & becker Pages: 4

Liberty 50 Catalyzed 2019

Brand: PIAGGIO Pages: 62

KODIAK YFM70KDXM

Brand: Yamaha Pages: 180

Brand: Yamaha Pages: 156

RAPTOR 700R 2022

Brand: Yamaha Pages: 160

Brand: Yamaha Pages: 172

Brand: Yamaha Pages: 80

Brand: BMW Motorrad Pages: 28

Brand: BMW Motorrad Pages: 170

Brand: Vetter Pages: 11

Brand: Kuberg Pages: 38

Brand: Dräger Pages: 164

Brand: Brixton Pages: 148

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands