background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-1

6

EAU17231

Safety is an obligation of the owner. Pe-
riodic inspection, adjustment and lubri-
cation will keep your vehicle in the
safest and most efficient condition pos-
sible. The most important points of
motorcycle inspection, adjustment, and
lubrication are explained on the follow-
ing pages.

Maintenance, replacement, or repair
of the emission control devices and
systems may be performed by any
repair establishment or individual
that is certified (if applicable).

WARNING

EWA10320

If you are not familiar with mainte-
nance work, have a Yamaha dealer
do it for you.

EAU17300

PERIODIC MAINTENANCE 

PROPER PERIODIC MAINTENANCE
OF YOUR MOTORCYCLE IS IMPOR-
TANT IN ORDER TO ENJOY LONG,
PLEASURABLE SERVICE. ESPE-
CIALLY IMPORTANT ARE THE MAIN-
TENANCE SERVICES RELATED TO
EMISSIONS CONTROL. THESE
CONTROLS NOT ONLY FUNCTION
TO ENSURE CLEANER AIR, BUT
ARE ALSO VITAL TO PROPER EN-
GINE OPERATION AND MAXIMUM
PERFORMANCE. IN THE FOLLOW-
ING PERIODIC MAINTENANCE
CHARTS, THE SERVICES RELATED
TO EMISSIONS CONTROL ARE
GROUPED SEPARATELY. THESE
SERVICES REQUIRE SPECIALIZED
DATA, KNOWLEDGE, AND EQUIP-
MENT. YAMAHA DEALERS ARE
TRAINED AND EQUIPPED TO PER-
FORM THESE PARTICULAR SER-
VICES.

EAU17350

Owner’s tool kit 

The owner’s tool kit is located under the
rider seat. (See page 3-11.)
The service information included in this
manual and the tools provided in the
owner’s tool kit are intended to assist
you in the performance of preventive
maintenance and minor repairs. How-
ever, additional tools such as a torque
wrench may be necessary to perform
certain maintenance work correctly.

NOTE:

If you do not have the tools or experi-
ence required for a particular job, have
a Yamaha dealer perform it for you.

1. Owner’s tool kit

5JW11.book  Page 1  Friday, May 9, 2003  4:03 PM

Summary of Contents for FJR1300(S)




































































































Reviews: