Yamaha F9.9 Page 100 Owner'S Manual Download

Page: 100 / 112

Trouble Recovery

A. Have serviced by a Yamaha dealer.

Q. Is fuel joint connection incorrect?
A. Connect correctly.

Q. Is heat range of spark plug incorrect?
A. Inspect spark plug and replace it with rec-
ommended type.

Q. Is high pressure fuel pump drive belt bro-
ken?
A. Have serviced by a Yamaha dealer.

Q. Is engine not responding properly to shift
lever position?
A. Have serviced by a Yamaha dealer.

Engine vibrates excessively.

Q. Is propeller damaged?
A. Have propeller repaired or replaced.

Q. Is propeller shaft damaged?
A. Have serviced by a Yamaha dealer.

Q. Are weeds or other foreign matter tangled
on propeller?
A. Remove and clean propeller.

Q. Is motor mounting bolt loose?
A. Tighten bolt.

Q. Is steering pivot loose or damaged?
A. Tighten or have serviced by a Yamaha
dealer.

EMU29435

Temporary action in emergen-

EMU29442

Impact damage

WARNING

EWM00871

The outboard motor can be seriously
damaged by a collision while operating or
trailering. Damage could make the out-
board motor unsafe to operate.

If the outboard motor hits an object in the wa-
ter, follow the procedure below.

Stop the engine immediately.

Check the control system and all compo-
nents for damage. Also, check the boat
for damage.

Whether damage is found or not, return
to the nearest harbor slowly and careful-
ly.

Have a Yamaha dealer check the out-
board motor before operating it again.

EMU30684

Replacing fuse

If a fuse has blown, open the fuse holder and
remove the fuse with a fuse puller. Replace it
with a spare one of the proper amperage.

U6DR38E0.book Page 94 Tuesday, November 27, 2018 2:08 PM

Yamaha

Motor

Corporation

Summary of Contents for F9.9

















































































































Search results

Summary of Contents for F9.9

Reviews:

Related manuals for F9.9

Brands by name

Popular brands

Yamaha F9.9, Owner'S Manual

Search results

Summary of Contents for F9.9

Reviews:

Related manuals for F9.9

Brands by name

Popular brands