manualshive.com logo in svg

Yamaha F70AET, Rigging Manual

Share
Download
Yamaha F70AET Rigging Manual Download Page 239

7-6

OPTIONAL EQUIPMENT

NMEA2000 GATEWAY

Used to connect between NMEA2000 compatible equipment and network hub.

ANALOG GAUGE INTERFACE (IF)

Used to connect between analog gauge and network hub.

Part No.

Remarks

6Y9-8A2D0-20

Compatible with 6Y8 and 6Y9 protocols

Part No.

Remarks

6Y9-8A2D0-30

Compatible with 6Y8 and 6Y9 protocols, Required for each engine.

5.5

(0.22)

20.5

(0.

8

1)

116 (4.57)

130 (5.12)

To 

N

MEA2000

e

qu

ipment

To net

w

ork h

ub

v

ia 

w

ire-lead

6Y9-

8

3553-50

12 (0.47)

1.

8

 (0.07)

4.

8

 (0.19)

56 (2.20)

7.

8

 (0.31)

500 (19.7)

20

YELLO

W

mm (in.)

1.

8

 (0.07)

4.6 (0.1

8

)

7.

8

 (0.31)

To 

w

ire-harness

6Y5-

8

3553-00

To analog 
tachometer 

v

ia 

trim/oil lead
6Y5-

8

3653-*0

To h

ub

v

ia 

w

ire-lead

6Y9-

8

3553-50

12

(0.47)

16 (0.63)

116 (4.57)

130 (5.12)

400 (15.

8

)

Engine selection for analog tachometer:

56 (2.20)

5.5 
(0.22)

20.5

(0.

8

1)

B

Or

B

L

B

Or

B

L

B

Or

B

L

B

Or

B

L

—

—

—

—

—

CE

N

TER engine

CE

N

TER PORT engine

CE

N

TER STBD engine

STBD engine

PORT engine

PORT engine

PORT engine

PORT engine

Q

u

ad engine

Single engine

T

w

in engine

Triple engine

—

STBD engine

STBD engine

30

mm (in.)

Summary of Contents for F70AET










































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands