Yamaha F30 Owner'S Manual Download Page 62 | Manualshive

Page: 62 / 120

background image

Operation

56

EMU43782

Sending fuel (portable tank)

When using the portable fuel tank “A”, send
fuel to the outboard motor according to the
following procedure.

1. Loosen the air vent screw 2 or 3 turns.

2. Align the fuel joint on the fuel hose with

the fuel joint on the outboard motor.
While pinching the fuel joint on the fuel
hose, securely connect the fuel hose to
the fuel joint on the outboard motor.
Then securely connect the other end of
the fuel hose to the fuel joint on the fuel
tank.

3. Wipe up any spilled gasoline immediate-

ly with dry rags.

TIP:

Dispose rags properly according to local
laws or regulations.
4. Squeeze the primer pump, with the ar-

row pointing up, until you feel it become
firm. During engine operation place the
tank horizontally, otherwise fuel cannot
be drawn from the fuel tank.

1. Air vent screw

ZMU07595

å

1

ZMU07598

1. Fuel joint
2. Fuel hose

1. Fuel joint
2. Fuel hose

1

2

ZMU07584

2

1

ZMU07585

6BG-9-3F-E0.book 56 ページ２０１８年１１月１日　木曜日　午後５時１分

©2020

Yamaha

Motor

Corporation

«
...
60
61
62
63
64
...
»

Summary of Contents for F30

























































































































Reviews:

No comments

Related manuals for F30

Brand: NXP Semiconductors Pages: 12

Brand: Supero Pages: 105

Brand: AOpen Pages: 8

Brand: Texas Instruments Pages: 23

Brand: Abit Pages: 48

Brand: ASROCK Pages: 145

AR0832MBSC25SUFAH-GEVB

Brand: ON Semiconductor Pages: 6

Brand: Gigabyte Pages: 96

Brand: Gigabyte Pages: 80

Brand: Advantech Pages: 82

Brand: Aaeon Pages: 56

Brand: SOYO Pages: 94

Brand: JETWAY Pages: 57

Brand: TYAN Pages: 96

Brand: Gigabyte Pages: 104

Brand: CAME Pages: 8

Brand: DFI Pages: 73

Super 7 SY-5SSM

Brand: SOYO Pages: 86

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands