background image

Engine control system

44

If the alert device has activated, stop the en-
gine as soon as it is safe to do so. Check the
oil level and add oil as needed. If the oil level
is correct and the alert device does not
switch off, consult your Yamaha dealer.
Twin engine drive users:
If the low oil pressure alert system of one en-
gine activates, both engines will slow down
and the buzzer will sound. To switch off the
alert activation on the engine not affected by
low oil pressure, turn off the main switch of
the engine with the low oil pressure.

EMU41942

Water separator alert

The outboard motor is equipped with a water
separator alert system. If water separated
from the fuel exceeds a specific volume, the
alert system will activate.

The water separator-alert indicator of the
6Y8 Multifunction Tachometer will come
on or blink.

The pop-up window will appear on the
Multi-Display.

The buzzer will sound intermittently when
the control lever is in the neutral position.

If the alert system has activated, stop the en-
gine immediately and see page 90 of this
manual to drain the water from the fuel filter.
Get back to the port soon and consult a
Yamaha dealer immediately.

ZMU07155

ZMU07156

ZMU05423

ZMU05424

ZMU07242

U6DV72E0.book  Page 44  Friday, December 19, 2014  3:38 PM

Summary of Contents for F200G









































































































Reviews: