Yamaha F200G Owner'S Manual Download Page 43 | Manualshive

Page: 43 / 104

background image

Instruments and indicators

37

Stop the engine immediately if the buzzer
sounds and the overheat alert device has ac-
tivated. Check the cooling water inlet for
clogging.

NOTICE

ECM01593



Do not continue to run the engine if the
overheat-alert indicator blinks. Serious
engine damage will occur.



Do not continue to operate the engine if
a alert device has activated. Consult
your Yamaha dealer if the problem can-
not be located and corrected.

EMU36151

Water separator alert

This indicator will blink if water has accumu-
lated in the water separator (fuel filter) while
cruising. In such an event, stop the engine
immediately and see page 90 of this manual
to drain the water from the fuel filter. Get back
to the port soon and consult a Yamaha dealer
immediately.

NOTICE

ECM00911

Gasoline mixed with water could cause
damage to the engine.

EMU36161

Engine trouble alert

This indicator will blink if the engine malfunc-
tions while cruising. Get back to the port
soon and consult a Yamaha dealer immedi-
ately.

ZMU05422

ZMU05423

ZMU05424

ZMU05425

U6DV72E0.book Page 37 Friday, December 19, 2014 3:38 PM

«
...
41
42
43
44
45
...
»

Summary of Contents for F200G









































































































Reviews:

No comments

Related manuals for F200G

Brand: AMPTRON Pages: 41

FEBFL7701_L31H008A

Brand: Fairchild Pages: 24

TPS53355EVM-864

Brand: Texas Instruments Pages: 29

Brand: JETWAY Pages: 58

Brand: ST Pages: 22

Brand: ASROCK Pages: 154

Z690M DS3H DDR4

Brand: Gigabyte Pages: 36

790XT-G35 series

Brand: MSI Pages: 103

Brand: Microchip Technology Pages: 34

Brand: MSI Pages: 171

Brand: Gigabyte Pages: 96

Brand: Microchip Technology Pages: 2

Brand: Gigabyte Pages: 112

Brand: Texas Instruments Pages: 17

MT9M031I12STCH-GEVB

Brand: ON Semiconductor Pages: 5

Brand: COX Pages: 60

Brand: IDT Pages: 39

Brand: One Control Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands