Yamaha F200D Owner'S Manual Download Page 53

Page: 53 / 81

Maintenance

NOTE:

When operating in salt water, turbid or muddy water, the engine should be flushed with clean
water after each use.

EMU28871

Maintenance chart (additional)

EMU28910

NOTE:

When using lead or high-sulfur gasoline, inspecting valve clearance may be required more fre-
quently than every 500 hours.

Water pump

Inspection

Engine oil

Inspection / change

Oil filter (cartridge)

Change

Spark plug(s)

Cleaning / adjustment /
replacement

Timing belt

Inspection /
replacement

Item

Actions

Every

500 hours (2.5 years)

1000 hours (5 years)

Timing belt

Replacement

Timing chain / chain
tensioner

Inspection

Valve clearance
(DOHC)

Inspection / adjustment

Item

Actions

Initial

Every

10 hours

(1 month)

50 hours

(3 months)

100 hours

(6 months)

200 hours

(1 year)

U69J14E0.book Page 47 Friday, March 12, 2004 10:20 AM

Summary of Contents for F200D


















































































Search results

Summary of Contents for F200D

Reviews:

Related manuals for F200D

Brands by name

Popular brands

Yamaha F200D, Owner'S Manual

Search results

Summary of Contents for F200D

Reviews:

Related manuals for F200D

Brands by name

Popular brands