manualshive.com logo in svg

Yamaha F200D, Owner'S Manual

Share
Download
Yamaha F200D Owner'S Manual Download Page 39

Operation

33

hole is blocked. Consult your Yamaha
dealer if the problem cannot be located
and corrected.

●

If the cooling passage is frozen, it may
take awhile for water to start flowing out
of the pilot hole.

EMU27740

Shifting

WARNING

EWM00180

Before shifting, make sure there are no
swimmers or obstacles in the water near
you.

CAUTION:

ECM00220

To change the boat direction or shifting
position from forward to reverse or vice-
versa, first close the throttle so that the en-
gine idles (or runs at low speeds).

EMU27763

Forward (tiller handle and remote 
control models)

Tiller control models
1.

Place the throttle grip in the fully closed
position.

2.

Move the gear shift lever quickly and firm-
ly from neutral to forward.

Remote control models
Pull up the neutral interlock trigger (if
equipped) and move the remote control lever
quickly and firmly from neutral to forward.

EMU27784

Reverse (automatic reverse lock and 
power trim and tilt models)

WARNING

EWM00190

When operating in reverse, go slowly. Do
not open the throttle more than half. Other-
wise the boat could become unstable,
which could result in loss of control and
an accident.

Tiller control models
1.

Place the throttle grip in the fully closed
position.

2.

Move the gear shift lever quickly and firm-
ly from neutral to reverse.

N

F

ZMU04597

U69J14E0.book  Page 33  Friday, March 12, 2004  10:20 AM

Summary of Contents for F200D


















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands