Yamaha F150G Page 21 Owner'S Manual Download | Manualshive

Page: 21 / 104

background image

Specifications and requirements

14

EMU41953

Engine oil requirements

Select an oil grade according to the average
temperatures in the area where the outboard
motor will be used.

If oil grades listed under Recommended en-
gine oil grade 1 are not available, select an al-
ternative oil grade listed under
Recommended engine oil grade 2.

Recommended engine oil grade 1

Recommended engine oil grade 2

EMU36361

Fuel requirements

EMU44860

Gasoline

Use a good quality gasoline that meets the
minimum octane rating.

NOTICE

ECM01982



Do not use leaded gasoline. Leaded
gasoline can seriously damage the en-
gine.



Avoid getting water and contaminants in
the fuel tank. Contaminated fuel can
cause poor performance or engine dam-
age. Use only fresh gasoline that has
been stored in clean containers.

Gasohol

There are two types of gasohol: gasohol con-
taining ethanol (E10) and that containing
methanol. Ethanol can be used if the ethanol

Recommended engine oil:

YAMALUBE 4 or 4-stroke outboard
motor oil

Recommended engine oil grade 1:

SAE 10W-30/10W-40/5W-30
API SE/SF/SG/SH/SJ/SL

Recommended engine oil grade 2:

SAE 15W-40/20W-40/20W-50
API SH/SJ/SL
Engine oil quantity (without oil filter
replacement):

4.3 L (4.55 US qt, 3.78 Imp.qt)

Engine oil quantity (with oil filter re-
placement):

4.5 L (4.76 US qt, 3.96 Imp.qt)

ZMU06854

122˚F

50˚C

104

40

86

30

68

SAE

API

SE
SF

SG
SH

SJ
SL

20

50

10

32

0

14

-10

-4

-20

10W–30

10W–40

5W–30

Recommended fuel:

Premium unleaded gasoline
(F200GET, FL200GET)
Regular unleaded gasoline (F150GET,
F175CET, FL150GET, FL175CET)

Min. pump octane number (PON):

89 (F200GET, FL200GET)

Min. research octane number (RON):

90 (F150GET, F175CET, FL150GET,
FL175CET)
94 (F200GET, FL200GET)

ZMU06855

122˚F

50˚C

104

40

86

30

68

SAE

API

SH

SJ
SL

20

50

10

32

0

14

-10

-4

-20

15W–40

20W–40

20W–50

U6DV75E0.book Page 14 Tuesday, February 21, 2017 8:33 AM

«
...
19
20
21
22
23
...
»

Summary of Contents for F150G









































































































Reviews:

No comments

Related manuals for F150G

Brand: Infineon Pages: 24

Brand: AOpen Pages: 8

Brand: Biostar Pages: 72

Brand: Gigabyte Pages: 44

otometrics HI-PRO 2

Brand: natus Pages: 22

Brand: DFI Pages: 60

CLICKER 4 for STM32

Brand: Mikroe Pages: 16

Brand: Supermicro Pages: 142

Brand: ASROCK Pages: 95

Brand: Mercury Pages: 57

Brand: Avalue Technology Pages: 29

Brand: Gigabyte Pages: 96

Brand: Biostar Pages: 60

EVB-LAN9252-SPI

Brand: Microchip Technology Pages: 22

Brand: J&W Pages: 39

Brand: IEPC Pages: 9

Brand: IEI Technology Pages: 43

Brand: ASROCK Pages: 83

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands